American
Data Supply Is Your One Source For All Your Cable Tray-Cable Trays- Cable Tray
Systems- Basket Tray- Raceway Systems
Plenum Innerduct
is a cable tray supplier, raceway systems distributor and carries and Cable Trays
from Cable Manger, Cablofil, SnakeTray, ICC, Newton and Hendry (now Telect) Due
to Cable-Mgr.'s innovative cable tray and extensive cable tray systems design
which are based on pre-fabricated junctions/intersections and the ability to provide
powder coated finishes while maintaining grounding-The design eliminates the need
to cut or bend sections or install a separate ground wire. Cable-Mgr. is U.L.
classified as to its suitability as an equipment grounding conductor only.No connecting
hardware required. All support hardware available. Powder coating is standard
finish.Custom sizes available. Furthermore, Cable-Mgr.'s wire grid cable tray
systems require only one tool and very few accessory items for installation. Pre-fabricated
junctions/intersections reduce man-hours by eliminating cutting and fabrication
in the field. With center hung trapeze, wall or floor mount accessories, Cable-Mgr.
is prepared to handle the toughest installations.
Cable-Mgr-Save
50% On Installation Costs-How To Install
We
now accept Visa,Discover Master Card & AMEX
Cablofil
Cable Tray ProductsClick
Snaketry
Cable TraysClick
Key
Features- Applications
• Requires NO bending or cutting; ready–made 4-way, “T” and
“L” shaped junctions
• Conforms to the National Electric Code,
UL Classified
• Acts as a continuous ground conductor; no grounding splices
• Adapts to difficult architectural designs to accommodate changes in direction
and elevation of cable runs
• Cuts installation time up to 50 percent
• Provides strength, rigidity without additional hardware; has smooth edges
• Manufactured in an array of protective, powder-coated, colored finishes
to minimize corrosion
• Featured in light or heavy duty product styles
• All support hardware available
• Powder coating is standard finish
• Custom sizes available
Cable
Tray Straight Sections
|
|
|
Atraight
sections have a grid pattern of 2 inches x 2 inches or 2 inches x 4 inches and
are available in standard widths from 2 inches up to 24 inches. Lengths can be
ordered in
1, 2, 5, 8 and 10 feet with a depth/height of either 2, 4 or 6 inches.
See finish chart for standard colors; safety yellow is the standard. Custom sizes
and colors are available.Sections include interconnecting hardware.
Pre-fabricated
junctions have a grid pattern of 2 inches x 2 inches or 2 inches x 4 inches and
are available in standard widths from 2 inches up to 24 inches with a depth/height
of
2, 4 or 6 inches. Junctions/intersections lengths are standard: 12 inches
wide or less come
2 feet in length and junctions/intersections more than 12
inches wide come 3 feet in length. All drops are available in 12, 18 or 24 inches
in lengthSee finish chart for colors; safety yellow is the standard. Custom colors
are availableJunctions/intersections include interconnecting hardware.
Pre-fabricated
reducers are available in standard configurations with a grid pattern of 2 inches
x 2 inches or 2 inches x 4 inches or and a depth/height of 2, 4 or 6 inches. All
reducers are
2 feet in length.See finish chart for standard colors; safety
yellow being the standard. Custom colors are available.Sections include interconnecting
hardware.
Cable
Tray Hardware & Accesorries
|
|
|
The
NOS EZFieldMate™ Field Termination Kit offers a simple, efficient, and cost-effective
process for field connectorization of single mode or multi-mode fiber optic cable
at the tightest factory specifications. Minimal training is required for installers
and technicians to become proficient and certified. The kit includes all tools,
parts and instructions needed to complete the termination of fibers in the field,
which are compliant with GR-326-CORE & Telcordia GR-1081-CORE requirements.
NOS can customize the kits to contain various connector types/polishes to meet
customer needs.
|
Pro 10 Wire Cable Tray |
M.E.2 Wire Cable Tray |
Cable-Mgr.
should be installed from the originating head-end i.e., the electrical or telecommunications
closet. Once the pathway has been established, it is important the layout of the
pre-fabricated junctions be installed first. Junctions/intersections lengths are
standard: 12 inches wide or less come 2 feet in length and junctions/intersections
more than 12 inches wide come 3 feet in length. This allows for field measurements
to be taken before installing the cable tray. If the straight sections are installed
first, it will cause unnecessary field adjustments. Each section has loops at
each end. When the sections are connected, the loop on the bottom aligns under
the galvanized masked area of the adjoining section. The loop on the side slides
into the outside loop guide. Once the trays are aligned, install the 5/16 inch
carriage bolt (included) through the loops with the treaded end to the outside
of the tray. Install and tighten the flanged nuts with a ½ inch socket.
This reduces the chances of damage when pulling the cables. Elevation may be adjusted
by using pre-fabricated drop with universal hooks (Fig. 1) or individual straight
sections with universal hooks and extenders (Fig. 2). Adjust the length with the
Cable-Mgr. cable tray extensions CM-58 (Fig. 3). The extensions fit into the side
guides facilitating adjustment of the tray up to 6 inches on each end. It is not
recommended that the cable tray be cut as it will interfere with the grounding
characteristics and UL classification..
Cable-Mgr.'s
innovative design is based on pre-fabricated junctions/intersections and the ability
to provide powder coated finishes while maintaining ground. The design eliminates
the need to cut or bend sections or install a separate ground wire. Cable-Mgr.
is U.L. classified as to its suitability as an equipment grounding conductor only.No
connecting hardware required. All support hardware available. Powder coating is
standard finish.Custom sizes available.
What
is Cable Tray?
1. What is a Cable Tray System?
2. What standards / guidelines are available
for cable tray systems?
3. What types of Cable Tray are available?
4.
How do I know what type of cable tray is right for my application?
5. What
materials / finishes are available for the various cable tray systems?
6.
Now that I know what types of cable trays are available, what configurations are
available?
7. After selecting the type of cable tray and configuration required,
what support methods are available?
8. Before selecting the type of cable
tray, cable tray configuration(s), and support method desired, what additional
information do I need to supply to the cable tray manufacturer for them to best
understand and satisfy my needs?
What
is a Cable Tray System?
Per
the National Electrical Code, a cable tray system is "a unit or assembly
of units or sections and associated fittings forming a rigid structural system
used to securely fasten or support cables and raceways."
What does this
mean?
* Cable trays support cable the way that roadway bridges support traffic.
* A bridge is a structure that provides safe passage for traffic across open spans.
* Cable tray is the bridge that allows for safe transport of wires across open
spans.
* Therefore, think of cable tray as the structural component of a building's
electrical system.
What
standards / guidelines are available for cable tray systems?
1. The National Electrical Code publishes the standards for all types of electrical
applications. Articles 318, 250, and 800 cover various aspects of cable tray systems.
2. NEMA, (National Electrical Manufacturers Association), is an association comprised
of the major cable tray manufacturers in the industry. This committee has published
three documents to date: NEMA VE1, FG1 and VE2.
NEMA VE1 covers general cable tray definitions, manufacturing standards, performance
standards, test standards, and application information. Free download of this
document is available on the NEMA website.
NEMA FG1 addresses the standards for fiberglass cable tray systems. Free download
of this document is available on the NEMA website.
NEMA VE2 is a cable tray installation guideline which covers receiving and unloading
material, storage of material, and general installation practices. Free download
of this document is available on the NEMA website.
3. CTI, (Cable Tray Institute),
is a trade association comprised of the major cable tray manufacturers in the
industry and was formed to provide specifiers, designers, and installers information
on the advantages of using cable tray systems over other types of products. (i.e.
conduit, ladder rack, etc.)
What
types of Cable Tray are available?
1. Ladder Cable Tray
2. Solid Bottom Cable Tray
3. Trough Cable Tray
4. Channel Cable Tray
5. Wire Mesh Cable Tray
6. Single Rail Cable Tray
How
do I know what type of cable tray is right for my application?
1. Ladder Cable Tray provides:
1. Solid side rail protection and system strength
with smooth radius fittings and a wide selection of materials and finishes.
2. maximum strength for long span applications
standard widths of 6,12,18,
24, 30, and 36 inches
3. standard depths of 3, 4, 5, and 6 inches
4. standard
lengths of 10, 12, 20 and 24 feet
5. rung spacing of 6, 9, 12, and 18 inches
Ladder cable tray is generally used in applications with intermediate to
long support spans, 12 feet to 30 feet.
2. Solid Bottom Cable Tray provides:
1. Nonventilated continuous support for delicate cables with added cable protection
available in metallic and fiberglass.
2. Solid bottom metallic with solid
metal covers for nonplenum rated cable in environmental air areas
3. standard
widths of 6, 12, 18, 24, 30, and 36 inches
4. standard depths of 3, 4, 5,
and 6 inches
5. standard lengths of 10, 12, 20 and 24 feet
Solid Bottom
cable tray is generally used for minimal heat generating electrical or telecommunication
applications with short to intermediate support spans of 5 feet to 12 feet.
3. Trough Cable Tray provides:
1. Moderate ventilation with added cable
support frequency and with the bottom configuration providing cable support every
4 inches. Available in metal and nonmetallic materials.
2. standard widths
of 6, 12, 18, 24, 30, 36 inches
3. standard depths of 3, 4, 5, and 6 inches
4. standard lengths of 10, 12, 20 and 24 feet
5. fixed rung spacing of 4 inch
on center
Trough cable tray is generally used for moderate heat generating
applications with short to intermediate support spans of 5 feet to 12 feet.
4. Channel Cable Tray provides:
1. an economical support for cable drops
and branch cable runs from the backbone cable tray system.
2. standard widths
of 3, 4, and 6 inches in metal systems and up to 8 inches in nonmetallic systems.
3. standard depths of 1¼-1¾ inches in metal systems and 1, 1 1/8,
1 5/" and 2 3/16 inches in nonmetallic systems
4. standard length of
10, 12, 20 and 24 feet
Channel cable tray is used for installations with
limited numbers of tray cable when conduit is undesirable. Support frequency with
short to medium support spans of 5 to 10 feet.
5. Wire Mesh Cable Tray
provides:
1. A job site, field adaptable support system primarily for low
voltage, telecommunication and fiber optic cables. These systems are typically
steel wire mesh, zinc plated.
2. standard widths of 2, 4, 6, 8, 12, 16, 18,
20, and 24 inches
3. standard depths of 1, 2, and 4 inches
4. standard
length of about 10 feet (118")
Wire Mesh tray is generally used for
telecommunication and fiber optic applications and are installed on short support
spans, 4 to 8 feet.
6. Single Rail Cable Tray provides:
1. These
aluminum systems are the fastest systems to install and provide the maximum freedom
fort cable to enter and exit the system.
2. Single hung or wall mounted systems
in single or multiple tiers.
3. Standard widths are 6, 9, 12, 18, and 24 inches.
4. Standard depths are 3, 4, and 6 inches.
5. Standard lengths are 10 and
12 feet.
Single Rail Cable Tray is generally used for low voltage and power
cables installations where maximum cable freedom, side fill, and speed to install
are factors.
What
materials / finishes are available for the various cable tray systems?
1. Steel (Min. Yield = 33KSI) (35 KSI for Stainless)
1. Plain: hot rolled
pickled and oiled steel per ASTM A569 (Commercial Quality) or A570 (Structural
Quality)
2. Pre-Galvanized: mill galvanized steel per ASTM A653 CS (Commercial)
or SS (Structural) G90
3. Hot Dip Galvanized After Fabrication: plain steel
which is hot dipped after fabrication per ASTM A123.
4. Stainless Steel: type
304 or 316L fully annealed stainless steel
2. Aluminum (Min.Yield =
23 KSI)
1. 6063-T6 or 5052-H32 alloy per ASTM B209
3. Fiber Reinforced
Plastic (FRP)
1. Polyester and Vinyl Ester resin systems available
2.
meet ASTM E-84 smoke density rating; Polyester 680, Vinyl Ester 1025
3. Class
1 Flame Rating and self-extinguishing requirements of ASTM D-635.
Now
that I know what types of cable trays are available, what configurations are available?
1. Straight sections are available to route cables in a horizontal or vertical
plane.
2. Fittings are available to route cables in various directions in
either the horizontal or vertical planes. Typical examples of fittings include
elbows, tees, crosses, and risers. Each of these fittings are available in various
radii and bend angles.
3. Covers are accessories and shouldn't be in here
unless splices etc. are included.
After
selecting the type of cable tray and configuration required, what support methods
are available?
1. Trapeze Support (Single or Multi-tier)
2. Hanger rod clamps, "J"
hangers
3. Center Hung Support
4. Wall Support
5. Underfloor Support
6. Pipe stanchions or other structures
Each
of these support methods are preferable in different applications. For instance,
trapeze supports may be desired in an application where cables will be pulled
through the cable tray. Center hung supports, on the other hand, are generally
used when cables will be installed from the side of the cable tray. Center hung
supports are especially useful when future cable additions are desired. Wall supports
and underfloor supports are useful when ceiling structure is not available or
undesired. Outdoor installations are controlled by the structures available to
support the cable tray.
Before selecting the type of cable tray, cable tray
configuration(s), and support method desired, what additional information do I
need to supply to the cable tray manufacturer for them to best understand and
satisfy my needs?
1. Where? Job site and installation considerations
1. Outdoor
1. supports
available affect the length and strength requirements
2. environmental loads,
ice, wind, snow, and possibly seismic
3. corrosion requirements affect the
materials and finishes
4. classified hazardous locations affect the cable
types acceptable
2. Indoor
1. support locations available affect the
length and strength of the system
2. industrial installation may require a
200 lb. Concentrated Load
3. commercial or institutional installation may
make system appearance, system weight, and space available important factors
4. environmental air handling area may affect cable types, cable tray material,
or cable tray type and need for covers
5. classified hazardous locations affect
the cable types acceptable
2. What?
1. Type and number of cables to support
1. NEC cable fill requirements
dictate size, width and depth, of system
2. cable support requirement may
control bottom type
3. largest bending radius of cable controls fitting radius
4. total of cable weight determines load to support
2. Future requirements
1. cable entry / exit freedom
2. design partially full or an expandable system
3. support type to allow for needs
We’re
here to help you solve your business challenges and increase your ability to meet
your own customers’ growing expectations from their telecommunications service
providers.
Cable
Manager • Requires NO bending or cutting;
ready–made 4-way, “T” and “L” shaped junctions•
Conforms to the National Electric Code, UL Classified• Acts as a continuous
ground conductor; no grounding splices• Adapts to difficult architectural
designs to accommodate changes in direction and elevation of cable runs•
Cuts installation time up to 50 percent
Plenum Innerduct will NOT
BE UNDERSOLD
