Hardware Kits

Cable Tray Support Brackets

C Support Bracket			L Support Bracket
Model	Length		Model	Length
05-CM24-04201	6"		05-CM18-04201	6"
05-CM24-04202	8"		05-CM18-04201	8"
05-CM24-04205	12"		05-CM18-04201	12"
05-CM24-04208	18"		05-CM18-04201	18"
05-CM24-04210	24"		05-CM18-04201	24"
C Support Bracket			L Support Bracket

Solid Bottom Plate

Model	Dimensions Width x Length
05-2-06BP	6” x 59”
05-2-08BP	8” x 59”
05-2-12BP	12” x 59”
05-2-18BP	18” x 59”
05-2-24BP	24” x 59”
• Galvanized steel or powder coated to provide a smooth protective surface for cable pulling • Can be supplied pre-assembled to cable trays or installed in the field with #05-2-500985 Splice Washer Assys. 4/plate • Available in easy to handle 59” lengths • Fits cable trays 6, 8, 12, 18 and 24 inches wide
Solid Bottom Plate

Cable Tray Cover

Model	Dimensions Width x Length
05-CM21-04	4" x 59”
05-CM21-06	6" x 59”
05-CM21-08	8" x 59”
05-CM21-12	12" x 59”
05-CM21-18	18" x 59”
05-CM21-24	24" x 59”
Cable Tray Cover

Cable Tray Raised Floor Pedestal Supports

05-CM74-3 Angle Pedestal Support Kit - includes (2) Angle Supports and (2) "U" clamps
Clamps fit up to a 1 ½” dis. Pedestal

05-CM75-3 Raised Floor Pedestal Bridge Support Kit - includes (1) Bridge Support and (2) "U" clamps
Spans 24 inch center to center floor pedestals up to 1 1/2" dia.

Center Support Installation Hardware

CM50 - 1/4 inch Threaded Rod Kit. Includes (2) 1/4 inch flat washer, (2) 1/4 inch nuts, (1) 6 inch silicione protective tube and (1) center support with hold down bracket. Threaded rod not included. CM51 - 3/8 inch Threaded Rod Kit. Includes (2) 3/8 inch flat washer, (2) 3/8 inch nuts, (1) 6 inch silicone protective tube and (1) center support with hold down bracket. Threaded rod not included.

Catalog Numbering System (example below is for an 8 inch center hung tray using 1/4 inch threaded rod)

CM 5008

Tray Widths: 2 inch = 02, 4 inch = 04, 6 inch = 06, 8 inch = 08, 12 inch = 12, 18 inch = 18, 24 inch = 24

Trapeze Support Installation Hardware

CM52 - 1/4 inch Threaded Rod Kit. Includes (4) 1/4 inch flat washers and (4) 1/4 inch nuts. Threaded rod not included.

CM53 - 3/8 inch Threaded Rod Kit. Inclueds (4) 3/8 inch flat washers and (4) 3/8 inch nuts. Threaded rod not included.

Catalog Numbering System (example below is for an 18 inch trapeze hung tray using 3/8 inch threaded rod)

CM 5318

Tray Widths: 6 inch= 06, 8 inch= 08, 12 inch= 12, 18 inch= 18, 24 inch= 24

Raised Floor Support

CM56 - Raised floor support, 4 inch height, available widths 2, 4, 6, 8, 12, 18 and 24 inches. Catalog Numbering System (example below is for an 8 inch wide raised floor support) CM56 08 Widths: 2 inch = 02, 4 inch = 04, 6 inch = 06, 8 inch = 08, 12 inch = 12, 18 inch = 18, 24 inch = 24

Universal Beam Clamp

Universal Beam Clamp for hanging of threaded rods The universal beam clamps are made from zinc plated steel and fit 5/8” max beam flange. 05-CM100 fits 1/4”-20 threaded rod in bottom or side tapped hole 05-CM101 fits 3/8”-16 threaded rod in bottom or side tapped hole

Connecting Hardware

Coupling Nuts CM60 1/4"-20 CM61 3/8"-16	Flat Washers CM62 1/4" CM63 3/8"	Finned Nuts CM65 1/4"-20 CM66 3/8"-16 CM67 5/16"-18	Carriage Bolts CM68 5/16"-18 x 3/4" CM72* 5/16"-18 x 1 1/4"	Protective Tubing CM69 6" for 1/4" & 3/8" rod
*For use with CM5803 and CM7003 only

Accessories

Center Support CM54xx Widths 02, 04, 06, 08, 12 inches	Trapeze Support CM55xx Widths 06, 08, 12, 18, 24 inches	Wall Mount* CM57xx Widths 02, 04, 06, 08, 12, 18, 24 inches	Tray Extension Offset Loop CM58 Ø.187" (use 4 per tray)
Curved Tray Extension CM58-5 (use 4 per tray)	Waterfall CM59 (4 inch width) Ø.187"	Universal Loop** CM70xx 02 = Ø.187" 03 = Ø.250"	Ratchet CM99
*Anchor to floor or wall using 3/8 inch bolt & washer. Anchor hardware not included. **Use 1 5/16 inch bolt on double loop end

• Requires NO bending or cutting; ready–made 4-way, “T” and “L” shaped junctions
• All sizes conforms to the National Electric Code, UL Classified
• Acts as a continuous ground conductor; with built in splices
• Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs
• Cuts installation time up to 50 percent
• Provides strength, rigidity without additional hardware; has smooth edges
• Manufactured in an array of protective, powder-coated, colored finishes to minimize corrosion
• Alternative finishes:
• Hot dip galvanized
• 304 stainless steel
• 316L stainless steel
• Powder coating is standard finish
• 2"x2" up to 6"x36" Custom sizes available

Innovative Design

PRO-10's innovative design is based on pre-fabricated junctions/intersections and the ability to provide powder coated finishes while maintaining ground. The design eliminates the need to cut or bend sections or install a separate ground wire. PRO-10 is UL classified as to its suitability as an equipment grounding conductor only.

No connecting hardware required. All support hardware available to match finish. Powder coating is standard finish.
Custom sizes available.

Installation

PRO-10's wire cable tray systems require only one tool and very few accessory items for installation. Pre-fabricated junctions/intersections reduce man-hours by eliminating cutting and fabrication in the field. With center hung trapeze, wall or floor mount accessories, PRO-10 is prepared to handle the toughest installations.

Customer Service

PRO-10's wire cable trays and accessories are available for quick delivery from stock. PRO-10 is made in the U.S.A., shortening lead and delivery time. For special applications, our customer service employees are eager to help in design and product availability.

Click on a section to learn more

Cable Tray Straight Sections Straight sections have a grid pattern of 2 inches x 2 inches or 2 inches x 4 inches and are available in standard widths from 2 inches up to 36 inches. Lengths can be ordered in 1, 2, 5, 8 and 10 feet with a depth/height of either 2, 4 or 6 inches. See finish chart for standard colors; Chrome is the standard. Custom sizes and colors are available. Sections include interconnecting hardware.

Cable Tray Junctions / Intersections Pre-fabricated junctions have a grid pattern of 2 inches x 2 inches or 2 inches x 4 inches and are available in standard widths from 2 inches up to 24 inches with a depth/height of 2, 4 or 6 inches. Junctions/intersections lengths are standard: 12 inches wide or less come 2 feet in length and junctions/intersections more than 12 inches wide come 3 feet in length. All drops are available in 12, 18 or 24 inches in length. See finish chart for colors; chrome is the standard. Custom colors are available. Junctions/intersections include interconnecting hardware.

Cable Tray Reducers Pre-fabricated reducers are available in standard configurations with a grid pattern of 2 inches x 2 inches or 2 inches x 4 inches or and a depth/height of 2, 4 or 6 inches. All reducers are 2 feet in length. See finish chart for standard colors; safety yellow being the standard. Custom colors are available. Sections include interconnecting hardware.

Cable Tray Accessories & Hardware Kits Accessories and hardware kits that provide support and cleanly finish the installation. With an assortment of threaded rod kits and various extensions, there is support for floor, wall or ceiling mounted cable tray options to conveniently complete the job. See finish chart for standard colors; chrome being the standard. Custom colors are available.