The M.E.2 cable management system is manufactured with rigid .187 diameter zinc plated steel wire, welded in a 2 inch x 4 inch grid. M.E.2 cable trays can be configured at the installation site. Seven or 10 foot straight tray sections are easy to handle. Two or 4 inch deep trays available in 6, 8, 12, 18 and 24 inch widths, offer a wide variety of wire channel routing and protection options. The 2 x 4 inch grid design facilitates simple cable break outs while supporting the cable. The open grid design prevents dirt and dust build-up experienced in closed cable trays. Changes in tray routing directions are made with factory fabricated “L,” “T,” and “X” type tray junctions. Reducer sections come in wider dimensions only where required, building in cost savings. Tray sections can be easily interconnected, using industry common splice washer clamps. M.E.2 trays can be mounted on walls or posts, on ceilings or installed under raised flooring with Cable-Mgr Hardware.
Features and Benefits
Factory fabricated junctions save installation time and cut costs.
Seven or 10 foot length straight tray sections can be cut to length or formed by cutting side wires to change routing elevation at the installation site.
2 x 4 inch grid provides easy cable routing in or out of tray sections.
Available metal tray divider for cable separation.
Rigid steel construction – Made in the USA.
M.E.2 Straight Section Part Numbers
Part No. / Profile
W x D x L
Tray Weight
Max # of cables @ 50% fill ratio*
Load capacity over a 5' span
Load capacity over a 10' span**
7' Lengths
05-2-06207
6" x 2" x 7'
6.94 lbs.
130
27 lbs./ft.
N/A
05-2-08207
8" x 2" x 7'
7.91lbs.
174
29 lbs./ft.
N/A
05-2-12207
12" x 2" x 7'
9.85 lbs.
260
34 lbs./ft.
N/A
05-2-18207
18" x 2" x 7'
12.83 lbs.
394
43 lbs./ft.
N/A
05-2-24207
24" x 2" x 7'
15.74 lbs.
527
52 lbs./ft.
N/A
05-2-06407
6" x 4" x 7'
7.59 lbs.
253
35 lbs./ft.
N/A
05-2-08407
8" x 4" x 7'
8.60 lbs.
331
48 lbs./ft.
N/A
05-2-12407
12" x 4 " x 7'
10.57 lbs.
496
52 lbs./ft.
N/A
05-2-18407
18" x 4" x 7'
13.52 lbs.
751
68 lbs./ft.
N/A
05-2-24407
24" x 4" x 7'
16.41 lbs.
998
69 lbs./ft.
N/A
10' Lengths
05-2-06210
6" x 2" x 10'
9.92 lbs.
130
27 lbs./ft.
14 lbs./ft.
05-2-08210
8" x 2" x 10'
11.12 lbs.
174
29 lbs./ft.
16 lbs./ft.
05-2-12210
12" x 2" x 10'
14.13 lbs.
260
34 lbs./ft.
19 lbs./ft.
05-2-18210
18" x 2" x 10'
18.33 lbs.
394
43 lbs./ft.
22 lbs./ft.
05-2-24210
24" x 2" x 10'
22.48 lbs.
527
52 lbs./ft.
23 lbs./ft.
05-2-06410
6" x 4" x 10'
10.84 lbs.
253
35 lbs./ft.
17 lbs./ft.
05-2-08410
8" x 4" x 10'
12.28 lbs.
331
48 lbs./ft.
25 lbs./ft.
05-2-12410
12" x 4" x 10'
16.00 lbs.
496
52 lbs./ft.
28 lbs./ft.
05-2-18410
18" x 4" x 10'
19.31 lbs.
751
68 lbs./ft.
31 lbs./ft.
05-2-24410
24" x 4" x 10'
23.45 lbs.
998
69 lbs./ft.
The M.E.2 cable management system is manufactured with rigid .187 diameter zinc plated steel wire, welded in a 2 inch x 4 inch grid. M.E.2 cable trays can be configured at the installation site. Seven or 10 foot straight tray sections are easy to handle. Two or 4 inch deep trays available in 6, 8, 12, 18 and 24 inch widths, offer a wide variety of wire channel routing and protection options. The 2 x 4 inch grid design facilitates simple cable break outs while supporting the cable. The open grid design prevents dirt and dust build-up experienced in closed cable trays. Changes in tray routing directions are made with factory fabricated “L,” “T,” and “X” type tray junctions. Reducer sections come in wider dimensions only where required, building in cost savings. Tray sections can be easily interconnected, using industry common splice washer clamps. M.E.2 trays can be mounted on walls or posts, on ceilings or installed under raised flooring with Cable-Mgr Hardware.
Features and Benefits
Field fabricated junctions allow for difficult installations.
Seven or 10 foot length straight tray sections can be cut to length or formed by cutting side wires to change routing elevation at the installation site.
2 x 4 inch grid provides easy cable routing in or out of tray sections.
Available metal tray divider for cable separation.
Rigid steel construction – Made in the USA.
Alternative finishes:
Hot dip galvanized
304 stainless steel
316L stainless steel
Wire Management Products
The Wiremaid U.S.A. Products Division of Vutec Corporation entered the cable tray arena with the development of PRO-10 and M.E.2 wire cable tray systems.
PRO-10 cable tray is an innovative and cost-effective system that easily adapts to the most difficult installations. Designed for the low voltage industry and developed with the architect, engineer and installer in mind, PRO-10's pre-fabricated junctions/intersections and ease of installation make it a cost-effective choice of contractors throughout the United States.
M.E.2 cable tray management system is manufactured with rigid .187 diameter zinc-plated steel wire, welded in a two inch by four inch grid facilitating easy cable break outs while supporting the cable. The open grid design prevents dirt build-up and dust experienced in closed cable trays.
PRO-10 Wire Cable Tray
Wiremaid U.S.A. has just created the "Cable Tray Maker,” an easy-to-use cable tray designer that takes the guess work out of ordering a cable tray system. Click on a cable tray part, choose your options and add the quantity. It creates a bill of materials that you can print or email.
• Requires NO bending or cutting; ready–made 4-way, “T” and “L” shaped junctions
• Acts as a continuous ground conductor; no grounding splices
• Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs
• Cuts installation time up to 50 percent
• Provides strength, rigidity without additional hardware; has smooth edges
• Manufactured in an array of protective, powder-coated, colored finishes to minimize corrosion
• Factory fabricated junctions save installation time and cut costs.
• Seven or 10 foot length straight tray sections can be cut to length or formed by cutting side wires to change routing elevation at the installation site.
• Two x 4 inch grid provides easy cable routing in or out of tray sections.
• Available metal tray divider for cable separation.
The M.E.2 cable management system is manufactured with rigid .187 diameter zinc plated steel wire, welded in a 2 inch x 4 inch grid. M.E.2 cable trays can be configured at the installation site. Seven or 10 foot straight tray sections are easy to handle. Two or 4 inch deep trays available in 6, 8, 12, 18 and 24 inch widths, offer a wide variety of wire channel routing and protection options. The 2 x 4 inch grid design facilitates simple cable break outs while supporting the cable. The open grid design prevents dirt and dust build-up experienced in closed cable trays. Changes in tray routing directions are made with factory fabricated “L,” “T,” and “X” type tray junctions. Reducer sections come in wider dimensions only where required, building in cost savings. Tray sections can be easily interconnected, using industry common splice washer clamps. M.E.2 trays can be mounted on walls or posts, on ceilings or installed under raised flooring with Cable-Mgr Hardware.
