ASTM E 814 Firestop Caulk- Firestop Foam-Firestop- Firestop Products-Firestop Supplier-Firestop Distributor- FireStop Protection
Abesco CT -120 -PRICE BELOW -Starting at $ 13.00
Part of the 'Abesco fireclamp system', CT120 Cable Transits are designed to prevent the spread of fire from one compartment to another where electrical, data, and communication cables penetrate through separating walls and floors. Part of the 'Abesco fireclamp system', CT120 Cable Transits are designed to prevent the spread of fire from one compartment to another where electrical, data, and communication cables penetrate through separating walls and floors. Abesco CT120 Cable Transits consist of a square section steel sleeve, which contains the heat reactive intumescent material. The unit has an integral hinged top which provides an easy retro-fit option where cables are pre-installed. Abesco CT Mounting Plates provide a quick and easy method of installing single or multiple CT120 Cable Transit.... even in drywall partitions.
What happens in a Fire Situation?
When exposed to the heat of a fire, the graphite based intumescent material contained in the Abesco CT120 Cable Transits expands rapidly to close and seal the inside of the sleeve, preventing the spread of fire from one compartment to another.
Why use Abesco CT120 Cable Transits?
Where to use Abesco CT120 Cable Transits Abesco CT120 Cable Transits are suitable for use in any building where electrical, data, or communication cables penetrate through fire rated compartment floors and walls, including drywall. Typical types of buildings where Abesco CT120 Cable Transits are commonly used are :
|
- May be joined together to form double or triple units using CT Mounting Flange Set (purchase separately)
- Underwriters Laboratory UL Classified 1 and 2 hour rating
- Tested in accordance with ASTM E814, UL1479, BS EN1366-3, BS 476 part 20, AS/NZ 1530
- Easy installation saves labor cost
- The Cable Transit firestop consist of a square steel sleeve with heat reactive graphite based intumescent material.
- If exposed to high temperatures of 300° F, the intumescent material will rapidly expand to form a solid insulating char plug to seal and prevent the passage of fire or smoke.
- Underwriters Laboratory UL Classified 1 and 2 hour rating
- Tested in accordance with ASTM E814, UL1479, BS EN1366-3, BS 476 part 20, AS/NZ 1530
CT-120R
Part of the 'Abesco fireclamp system', CT120/R Cable Transits are designed to prevent the spread of fire from one compartment to another where electrical, data, and communication cables penetrate through separating walls and floors.
A major benefit of the CT120 device is its ability to be fitted into situ without the use of any mechanical fittings. The full range of CT Mounting plates allow the CT120 devices to be banked together without any fixing to the wall or floor.
| PART # | DIMENSIONS | DESCRIPTION | PRICE |
| 2.5" Square | |||
| FP-CT31940 | 2.5" x 2.5" square x 10" length (65mm square) |
Cable Transit Firestop Device CT 120 - 2.5" x 2.5" square x 10" length |
$90.00 |
| CT 120 CT Mounting Flange Set | |||
| FP-CT31972 | 2.5" square | SINGLE Mounting Flange Set (2 pc. set for single part # FP-CT31940) Used to mount one 2.5 inch CT120 unit |
$16.95 |
| FP-CT31974 | 2.5" x 5" | DUPLEX Mounting Flange Set (2 pc. set for quantity (2) part # FP-CT31940) Used to mount two (2.5) inch CT120 units together side by side |
$21.95 |
| FP-CT31976 | 2.5" x 7.5" | TRIPLEX Mounting Flange Set (2 pc. set for quantity (3) part # FP-CT31940) Used to mount three (2.5) inch CT120 units together side by side |
$25.00 |
| 4" Square | |||
| FP-CT31942 | 4" x 4" square x 10" length (102mm square) |
Cable Transit Firestop Device CT 120 - 4" x 4" square x 10" length |
$119.00 |
| Mounting Flange Set | |||
| FP-CT31982 | 4" square | SINGLE Mounting Flange Set (2 pc. set for single part # FP-CT31942) Used to mount one 4inch CT120 unit |
$17.59 |
| FP-CT31984 | 4" x 8" | DUPLEX Mounting Flange Set (2 pc. set for quantity (2) part # FP-CT31942) Used to mount two (4) inch CT120 units together side by side |
$22.88 |
| FP-CT31986 | 4" x 12" | TRIPLEX Mounting Flange Set (2 pc. set for quantity (3) part # FP-CT31942) Used to mount three (4) inch CT120 units together side by side |
$26.40 |
| 2" Diameter | |||
| FP-CT31938 | 2" diameter x 10" length (51mm diameter round) |
Cable Transit Firestop Device CT 120 2" diameter x 10" length |
$91.00 |
| Mounting Flange Set | |||
| FP-CT31968 | 2" diameter round | CT 120 Mounting Flange Set 2 pc. Set for single part # FP-CT31938 |
$10.38 |
| 4" Diameter | |||
| FP-CT31950 | 4" diameter x 10" length (102mm diameter round) |
Cable Transit Firestop Device CT 120 - 4" diameter x 10" length |
$119.20 |
| Mounting Flange Set | |||
| FP-CT31998 | 4" diameter round | CT 120 CT Mounting Flange Set (2 pc. set for single part # FP-CT31950) |
$13.02 |
Plenum Innerduct is a national Firestop distributor and firestop supplier for a multitude of firestop products and carries a complete line of Firestop Products and Fire Stop Protection products. Our complete line of firestop fire protection products helps stop the spread of fire, smoke and toxic fumes. Our firestop fire protection produsts are easy to install and are approved for a wide variety of firestop applications by Underwriter’s Laboratories. Total passive firestop and 'fire' protection cannot be achieved with the use of a singular product. It is the use of many products designed for specific firestop applications that comprise a complete passive firestop fire protection systems. When installed properly, these firestop products work in concert with one another to create effective barriers against the passage of flames, smoke, and superheated gases. Used is conjunction with other firestop fire protection methods, properly installed passive fire protection will save lives, protect property, and minimize business losses.
Firestop and Firestopping is an integral part of fire protection engineering in all commercial buildings and are required by law in most states to satisfy mandated laws for commercial building fire protection. Firestop systems protect against the passage of flames, deadly gases and toxic smoke through openings that are created for penetrations, joints and gaps in fire-resistive walls, floors and floor/ceiling assemblies. The integrity of fire-rated assemblies is restored by firestop systems. Building codes require third-party tested systems to be installed whenever fire-rated construction is compromised by such openings.
 |
Telecomm cables found in a Hospital, the day before a Joint Commission Inspection. Cables were sleeved without having to be removed with our Split Sleeve & Bulkhead System. |  |
What is meant by "active" and "passive" fire protection?
Active fire suppression includes mechanical systems such as sprinklers, that are designed to extinguish fires after they have started. Passive fire protection functions to contain fires within the areas in which they start, preventing loss of life by preventing the products of combustion (smoke, hot gasses and flames) from spreading throughout a building.
Why is "passive" fire protection necessary?
Fire is a dangerous enough phenomenon that redundancy in fire protection is necessary. Having passive protection in place helps assure building occupants that there will be time to exit before gasses, fire and smoke spread throughout the building. If active systems fail, as they often do, then there is still a passive system in place for life safety.
It is the use of many products designed for specific firestop applications that comprise a complete passive firestop fire protection systems. When installed properly, these firestop products work in concert with one another to create effective barriers against the passage of flames, smoke, and superheated gases. Used is conjunction with other firestop fire protection methods, properly installed passive fire protection will save lives, protect property, and minimize business losses.
Joints
Construction joints must be sealed with joint systems, which will impart a fire resistance at least equal to those of the adjacent constructions so that overall fire resistance is not compromised.
Fire resistive joint systems are used in building construction to seal joints, and must be of the same or greater fire resistance (temperature) rating as the wall or floor containing the opening which they are designed to protect. Perimeter joint systems are most often used to seal a clearance separation between curtain walls and floors. They are designed to accommodate various movements induced
From the leader in fire protection...
Our manufacturer partners have been creating innovative firestop systems for more than 25 years. Our complete line of fire protection products helps stop the spread of fire, smoke and toxic fumes. They’re easy to install and are approved for a wide variety of firestop applications including but not all: Underwriter’s Laboratories, Factory Mutual and Omega Point Laboratories. Plenum Innerduct as a distributor can provide fully tested systems to firestop all of these scenarios:
- Structural steel
- Emergency circuitry
- Grease/air ducts
- Through penetrations
- Perimeter joints
- Fire resistive joints
ABESCO FIREFOAM RATINGS:
- Manufactured to ISO 9001:2000
- Corrosion resistant suitable for use in aggressive environments
- Certification for a wide range of cables Available in a range of sizes
- Very easy to install and provides total flexibility in cable routing
- Abesco graphite intumescent is unaffected by moisture
- Approved worldwide and recognized by independent authorities and tested in accordance with
- ASTM E-814 (UL 1479)
- BS 476
- AS 1530.4
- BS EN 1366-3
|
|
|||||||
 |
|
What is firestop?
Firestop and Firestopping is an integral part of fire protection engineering. Firestop systems protect against the passage of flames, deadly gases and toxic smoke through openings that are created for penetrations, joints and gaps in fire-resistive walls, floors and floor/ceiling assemblies. The integrity of fire-rated assemblies is restored by firestop systems. Building codes require third-party tested systems to be installed whenever fire-rated construction is compromised by such openings.
Firestop and Firestopping is an integral part of fire protection engineering in all commercial buildings and are required by law in most states to satisfy mandated laws for commercial building fire protection. Firestop systems protect against the passage of flames, deadly gases and toxic smoke through openings that are created for penetrations, joints and gaps in fire-resistive walls, floors and floor/ceiling assemblies. The integrity of fire-rated assemblies is restored by firestop systems. Building codes require third-party tested systems to be installed whenever fire-rated construction is compromised by such openings.
|
Telecomm cables found in a Hospital, the day before a Joint Commission Inspection. Cables were sleeved without having to be removed with our Split Sleeve & Bulkhead System. | |
What is meant by "active" and "passive" fire protection?
Active fire suppression includes mechanical systems such as sprinklers, that are designed to extinguish fires after they have started. Passive fire protection functions to contain fires within the areas in which they start, preventing loss of life by preventing the products of combustion (smoke, hot gasses and flames) from spreading throughout a building.
Why is "passive" fire protection necessary?
Fire is a dangerous enough phenomenon that redundancy in fire protection is necessary. Having passive protection in place helps assure building occupants that there will be time to exit before gasses, fire and smoke spread throughout the building. If active systems fail, as they often do, then there is still a passive system in place for life safety.
It is the use of many products designed for specific firestop applications that comprise a complete passive firestop fire protection systems. When installed properly, these firestop products work in concert with one another to create effective barriers against the passage of flames, smoke, and superheated gases. Used is conjunction with other firestop fire protection methods, properly installed passive fire protection will save lives, protect property, and minimize business losses.
Joints
Construction joints must be sealed with joint systems, which will impart a fire resistance at least equal to those of the adjacent constructions so that overall fire resistance is not compromised.
Additional Information -Applications Click Here
Fire resistive joint systems are used in building construction to seal joints, and must be of the same or greater fire resistance (temperature) rating as the wall or floor containing the opening which they are designed to protect. Perimeter joint systems are most often used to seal a clearance separation between curtain walls and floors. They are designed to accommodate various movements induced
From the leader in fire protection...
Our manufacturer partners have been creating innovative firestop systems for more than 25 years. Our complete line of fire protection products helps stop the spread of fire, smoke and toxic fumes. They’re easy to install and are approved for a wide variety of firestop applications including but not all: Underwriter’s Laboratories, Factory Mutual and Omega Point Laboratories. Plenum Innerduct as a distributor can provide fully tested systems to firestop all of these scenarios:
- Structural steel
- Emergency circuitry
- Grease/air ducts
- Through penetrations
- Perimeter joints
- Fire resistive joints
Please Visit Our Product Links Below:
CT 120 Cable Transits- Designed for single or multiple cables-easy to install and alter cabling-use in floPlenum Innerduct & walks-including drywall
Abesco CT120 Cable Transits are designed to prevent the spread of fire from one compartment to another where electrical, data, and communication cables penetrate through separating walls and floors.
Abesco CT120 Cable Transits consist of a square section steel sleeve, which contains the heat reactive intumescent material. The unit has an integral hinged top which provides an easy retro-fit option where cables are pre-installed. Abesco CT Mounting Plates provide a quick and easy method of installing single or multiple CT120 Cable Transits. even in drywall partitions.
WHY USE ABESCO CT120 CABLE TRANSITS ?
- Manufactured to ISO 9001:2000
- Corrosion resistant suitable for use in aggressive environments
- Certification for a wide range of cables Available in a range of sizes
- Very easy to install and provides total flexibility in cable routing
- Abesco graphite intumescent is unaffected by moisture
- Approved worldwide and recognized by independent authorities and tested in accordance with
- ASTM E-814 (UL 1479)
- BS 476
- AS 1530.4
- BS EN 1366-3
WHERE DO I USE ABESCO CT120 CABLE TRANSITS ?
Abesco CT120 Cable Transits are suitable for use in any building where electrical, data, or communication cables penetrate through fire rated compartment floors and walls, including drywall.
Typical types of buildings where Abesco CT120 Cable Transits are commonly used are :
Banking and finance buildings, data processing centers, TV and media studios, apartment buildings, hotels, office buildings, hospitals, airports, retail centers etc.
WHAT HAPPENS IN A FIRE SITUATION ?
When exposed to the heat of a fire, the graphite based intumescent material contained in the Abesco CT120 Cable Transits expands rapidly to close and seal the inside of the sleeve, preventing the spread of fire from one compartment to another.
Additional Firestop Links Below:
Alliance for Fire and Smoke Containment and Control (AFSCC)
The American Institute of Architects (AIA)
American National Standards Institute (ANSI)
American Society for Testing and Materials (ASTM)
Building Officials and Code Administrators International (BOCA)
Canadian Fire Safety Association (CFSA)
Factory Mutual Research Corp (FMRC)
OTHER PRODUCTS
Abesco supply a wide range of Firestop products which provide the specifier, engineer and contractor with cost effective solutions to most passive fire protection problems experienced on todays construction projects.
We will beat any US-Based Company's Price On Firestop - CableTray or Raceway!
Raceway System Solutions- Cable Tray Systems-Cable tray-Cable trays-Cable Tray Systems-Raceway Systems- Flextray-Basket Tray
Snake Tray Cabletray-Raceway Systems 
Snake Loop
Call Us Today Tollfree At (866) 342-3721 or (866) 650-DATA
Or Click On The Chat Button At The Top Of The Page To Talk To One Of Our Representatives
|
|
|
|
|
